参数资料
| 型号： | 9785 |
| 厂商： | 3M |
| 文件页数： | 7/33页 |
| 文件大小： | 0K |
| 描述： | HOT MELT APPLICATOR TIP |
| 标准包装： | 1 |
| 系列： | Scotch-Weld™ |
| 类型： | 电子端头 |
| 适用于相关产品： | 热融施用器 |
| 其它名称： | 2120082554 21200825545 3M10890 62978599306 9785-ND Q4418376 |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
Applicator Startup
!
Caution
Important:
Before proceeding, make sure the proper temperature module has been
Use only the proper temperature
module for the 3M? Quadrack?
adhesive used. Failure to do so
may cause burns or damage
applicator. Refer to Table 1 in the
Temperature Module Installation
installed. See previous section on Temperature Module Installation.
1. Plug the applicator into a grounded 120 VAC receptacle.
2. Push the on/off switch to the “on” position, indicated by the visible
red portion of the switch (see Figure B).
section for proper module selection
for 3M Quadrack adhesive used.
! Caution
Avoid contact with hot adhesive
and the applicator tip. May cause
burns. Wear safety glasses when
using.
Figure B
3. Wait 5 to 10 minutes for heat-up.
Note:
Allow at least 15 minutes for heat-up at its next use if the
applicator did not have adhesive extruded at shut-down. Refer
to shut-down procedure on page 12.
Important:
Thermal expansion can cause a small amount of adhesive to drip from
the tip during heat-up. With the proper temperature module selection,
the applicator should not drip after heat-up.
4. Inspect the nozzle tip. Use a Scotch-Brite ? pad or equivalent to
remove accumulated adhesive or foreign matter from the tip.
5
? 3M 2006
相关PDF资料 |
PDF描述 |
|---|---|
| 980892-000 | PRINTER RIBBONS |
| 983-009-010R011 | BACKSHELL DB9 BLACK PLASTIC |
| 983-10-FRA-4"X18" | CONSPICUITY MARKING 4"X 18" WHT |
| 987-1/2-36YD | TAPE ATG ADHESIVE TRANSFER 1/2" |
| 999-H15-PS2L571 | CONN HD15 FEMALE OVER DUAL PS/2 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 97-85-14 | 功能描述:环形MIL规格工具、五金与附件 PLATE SIZE 14 RoHS:否 制造商:Amphenol Industrial MIL 类型:MIL-DTL-5015 系列:97 产品类型:Dummy Receptacles 用于:97 Series Plugs |
| 97-85-18 | 功能描述:环形MIL规格工具、五金与附件 PLATE SIZE 18 RoHS:否 制造商:Amphenol Industrial MIL 类型:MIL-DTL-5015 系列:97 产品类型:Dummy Receptacles 用于:97 Series Plugs |
| 97-85-22 | 功能描述:环形MIL规格工具、五金与附件 PLATE RoHS:否 制造商:Amphenol Industrial MIL 类型:MIL-DTL-5015 系列:97 产品类型:Dummy Receptacles 用于:97 Series Plugs |
| 97-8522-24 | 制造商:TE Connectivity 功能描述:- Bulk |
| 97-8522-24-1 | 制造商:TE CONNECTIVITY 功能描述: |
发布紧急采购，3分钟左右您将得到回复。