参数资料
| 型号： | 9785 |
| 厂商： | 3M |
| 文件页数： | 24/33页 |
| 文件大小： | 0K |
| 描述： | HOT MELT APPLICATOR TIP |
| 标准包装： | 1 |
| 系列： | Scotch-Weld™ |
| 类型： | 电子端头 |
| 适用于相关产品： | 热融施用器 |
| 其它名称： | 2120082554 21200825545 3M10890 62978599306 9785-ND Q4418376 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
Troubleshooting (continued)
Condition 2:
Dripping nozzle
! Caution
Avoid contact with hot adhesive
and the applicator tip. May cause
burns. Wear safety glasses when
using.
1. Plug in the power cord of the applicator and turn it on. Follow
Applicator Startup Procedure on page 5 of Owner’s Manual.
Important:
Thermal expansion can cause a small amount of adhesive to drip from the
tip during heat-up. This is normal. If the nozzle continues to drip after a
warmup period of more than 10 minutes, then proceed to the next step.
2. Check to make sure that the proper temperature module is inserted into
the applicator for your adhesive. Refer to Table 1 on page 4 or the
chart on pages 29-30 (Temperature Module Selections section) for
selection of the proper temperature module to be used with your 3M?
Quadrack? adhesive. If the applicator continues to drip, proceed to
the next step.
3. Make sure that the adhesive is clean and not contaminated, and
proceed to the next step.
Backmelt Procedure:
4. If the adhesive stick is very difficult to extrude, check for backmelt:
a. Slowly push the adhesive stick into the applicator so stick is flush
with the white sleeve.
b. Remove stroke adjuster by firmly grasping and twisting upward
!
WARNING
(see Figure P).
Do not pull adhesive stick from the
rear of the applicator while in
operation. Removing adhesive
from the rear may cause molten
adhesive to flow out of the rear of
the applicator which may cause
burns or damage the applicator.
? 3M 2006
c. Remove the end clip by gently prying off one end of the clip
(see Figure P).
d. Remove the transport mechanism by sliding it off the entry track
(see Figure P).
e. Turn the applicator off by unplugging the power cord from the
outlet and pressing the rocker switch off. The red visor on the
rocker switch disappears, indicating the applicator is off
(see Figure N).
22
相关PDF资料 |
PDF描述 |
|---|---|
| 980892-000 | PRINTER RIBBONS |
| 983-009-010R011 | BACKSHELL DB9 BLACK PLASTIC |
| 983-10-FRA-4"X18" | CONSPICUITY MARKING 4"X 18" WHT |
| 987-1/2-36YD | TAPE ATG ADHESIVE TRANSFER 1/2" |
| 999-H15-PS2L571 | CONN HD15 FEMALE OVER DUAL PS/2 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 97-85-14 | 功能描述:环形MIL规格工具、五金与附件 PLATE SIZE 14 RoHS:否 制造商:Amphenol Industrial MIL 类型:MIL-DTL-5015 系列:97 产品类型:Dummy Receptacles 用于:97 Series Plugs |
| 97-85-18 | 功能描述:环形MIL规格工具、五金与附件 PLATE SIZE 18 RoHS:否 制造商:Amphenol Industrial MIL 类型:MIL-DTL-5015 系列:97 产品类型:Dummy Receptacles 用于:97 Series Plugs |
| 97-85-22 | 功能描述:环形MIL规格工具、五金与附件 PLATE RoHS:否 制造商:Amphenol Industrial MIL 类型:MIL-DTL-5015 系列:97 产品类型:Dummy Receptacles 用于:97 Series Plugs |
| 97-8522-24 | 制造商:TE Connectivity 功能描述:- Bulk |
| 97-8522-24-1 | 制造商:TE CONNECTIVITY 功能描述: |
发布紧急采购，3分钟左右您将得到回复。