参数资料
| 型号： | 9785 |
| 厂商： | 3M |
| 文件页数： | 21/33页 |
| 文件大小： | 0K |
| 描述： | HOT MELT APPLICATOR TIP |
| 标准包装： | 1 |
| 系列： | Scotch-Weld™ |
| 类型： | 电子端头 |
| 适用于相关产品： | 热融施用器 |
| 其它名称： | 2120082554 21200825545 3M10890 62978599306 9785-ND Q4418376 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
Troubleshooting (continued)
Condition 1:
Applicator
will not heat
! WARNING
Disconnect the electrical power and
make sure the applicator has cooled
to room temperature before
servicing. Failure to disconnect
electrical power or failure to allow
the applicator to cool before
servicing may cause electrical
shock or burns.
12. Inspect all terminal block connections for loose or disconnected wires
by making certain the screws in each terminal block are securing the
wires. If any connections are loose or have pulled out of the terminal
blocks, reconnect and retighten the connections (see Figures S and T).
After reconnections have been made, reassemble the applicator
making sure wiring is properly located and will not be pinched when
handles are closed (see Figures P, Q and R). Reinstall the previously
removed temperature module (see Figure O).
If all terminal block connections were initially found to be tight,
proceed to the next step.
Important:
Power switch MUST be in “on” position (red visor visible) for step 13.
13. Check electrical continuity of heater/TCO/switch assembly. Using an
ohmmeter, measure across the terminals numbered 3 and 4 on the top
terminal block labeled TB2. These are the terminal block positions
for the black wire from the power switch and the white wire from the
heater, respectively (see Figure S).
Value measured should be between 40-50 ohms. If measured value is
not in this range, replace the heater/TCO/switch assembly by ordering
3M? Heater Kit #62-9680-9731-1.
If measured value is within the specified range, proceed to the next
step.
19
TB2
123
Figure S
4
? 3M 2006
相关PDF资料 |
PDF描述 |
|---|---|
| 980892-000 | PRINTER RIBBONS |
| 983-009-010R011 | BACKSHELL DB9 BLACK PLASTIC |
| 983-10-FRA-4"X18" | CONSPICUITY MARKING 4"X 18" WHT |
| 987-1/2-36YD | TAPE ATG ADHESIVE TRANSFER 1/2" |
| 999-H15-PS2L571 | CONN HD15 FEMALE OVER DUAL PS/2 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 97-85-14 | 功能描述:环形MIL规格工具、五金与附件 PLATE SIZE 14 RoHS:否 制造商:Amphenol Industrial MIL 类型:MIL-DTL-5015 系列:97 产品类型:Dummy Receptacles 用于:97 Series Plugs |
| 97-85-18 | 功能描述:环形MIL规格工具、五金与附件 PLATE SIZE 18 RoHS:否 制造商:Amphenol Industrial MIL 类型:MIL-DTL-5015 系列:97 产品类型:Dummy Receptacles 用于:97 Series Plugs |
| 97-85-22 | 功能描述:环形MIL规格工具、五金与附件 PLATE RoHS:否 制造商:Amphenol Industrial MIL 类型:MIL-DTL-5015 系列:97 产品类型:Dummy Receptacles 用于:97 Series Plugs |
| 97-8522-24 | 制造商:TE Connectivity 功能描述:- Bulk |
| 97-8522-24-1 | 制造商:TE CONNECTIVITY 功能描述: |
发布紧急采购，3分钟左右您将得到回复。