- 您现在的位置：买卖IC网 > PDF目录98214 > TFA9812HN (NXP SEMICONDUCTORS) 15 W, 2 CHANNEL, AUDIO AMPLIFIER, PQCC48 PDF资料下载
参数资料
| 型号： | TFA9812HN |
| 厂商： | NXP SEMICONDUCTORS |
| 元件分类： | 音频／视频放大 |
| 英文描述： | 15 W, 2 CHANNEL, AUDIO AMPLIFIER, PQCC48 |
| 封装： | 7 X 7 MM, 0.85 MM HEIGHT, PLASTIC, MO-220, SOT619-8, HVQFN-48 |
| 文件页数： | 6/66页 |
| 文件大小： | 386K |
| 代理商： | TFA9812HN |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页
TFA9812_2
NXP B.V. 2009. All rights reserved.
Preliminary data sheet
Rev. 02 — 22 January 2009
14 of 66
NXP Semiconductors
TFA9812
BTL stereo Class-D audio amplier with I2S input
In I2C control mode communication is enabled after 4 ms. The preferred I2C settings can
be made within 66 ms before the PLL starts running. Finally, the output stages are
enabled and the audio level is increased via a demute sequence if mute has previously
been disabled.
Remark: In I2C mode soft mute is enabled by default. It can be disabled at any time while
I2C communication is valid. In order to prevent audio clicks volume control (default setting
is 0 dB) should be set before soft mute is disabled.
Remark: For a proper start-up in I2S master mode and I2C mode the following sequence
should be followed:
1. The I2S master setting should be set and keep the default sample rate setting active.
2. Next, another sample rate setting than the default one should be selected.
3. Finally, when the default sample rate is used the default sample rate setting should be
selected again.
8.3.2 Power-down
power-down.
Putting the TFA9812 into power-down is equivalent to enabling Sleep mode
(see Section 8.2.2). This mode is entered immediately and no additional clock cycles are
required.
In order to prevent audible clicks, soft mute should be enabled at least Td(soft_mute)
seconds before enabling Sleep mode.
The specied low current and power conditions in Table 1 are valid within 10
s after
enabling Sleep mode.
8.4 Digital audio data input
8.4.1 Digital audio data format support
The TFA9812 supports a commonly used range of I2S and I2S-like digital audio data input
formats. These are listed in Table 12.
Table 11.
Power-up/power-down selection
Power-up pin
value
Description
0
Power-down (Sleep mode)
1
Power-up
Table 12.
Supported digital audio data formats
BCK frequency Interface format (MSB rst)
Supported in I2C
control mode
Supported in Legacy
control mode
32 fs
I2S up to 16-bit data
yes
32 fs
MSB-justied 16-bit data
yes
32 fs
LSB-justied 16-bit data
yes
48 fs
I2S up to 24-bit data
yes
48 fs
MSB-justied up to 24-bit data
yes
相关PDF资料 |
PDF描述 |
|---|---|
| TFA9812HN/N1,518 | 15 W, 2 CHANNEL, AUDIO AMPLIFIER, PQCC48 |
| TFA9812HN/N1,557 | 15 W, 2 CHANNEL, AUDIO AMPLIFIER, PQCC48 |
| TFDS5500-TR3 | TRANSMITTER/RECEIVER IC, DMA8 |
| TFDT5500-TR3 | TRANSMITTER/RECEIVER IC, SMA8 |
| TFDU5100-TR3 | TRANSMITTER/RECEIVER IC, SMA8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TFA9812HN/N1,518 | 功能描述:IC AMP AUDIO 15W STER D 48HVQFN RoHS:是 类别:集成电路 (IC) >> 线性 - 音頻放大器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:DirectDrive® 类型:H 类 输出类型:耳机，2-通道（立体声） 在某负载时最大输出功率 x 通道数量:35mW x 2 @ 16 欧姆 电源电压:1.62 V ~ 1.98 V 特点:I²C，麦克风，静音，短路保护，音量控制 安装类型:表面贴装 供应商设备封装:25-WLP（2.09x2.09） 封装/外壳:25-WFBGA，WLCSP 包装:带卷 (TR) |
| TFA9812HN/N1,557 | 功能描述:IC AMP AUDIO 15W STER D 48HVQFN RoHS:是 类别:集成电路 (IC) >> 线性 - 音頻放大器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:DirectDrive® 类型:H 类 输出类型:耳机，2-通道（立体声） 在某负载时最大输出功率 x 通道数量:35mW x 2 @ 16 欧姆 电源电压:1.62 V ~ 1.98 V 特点:I²C，麦克风，静音，短路保护，音量控制 安装类型:表面贴装 供应商设备封装:25-WLP（2.09x2.09） 封装/外壳:25-WFBGA，WLCSP 包装:带卷 (TR) |
| TFA9815 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Stereo full-bridge audio amplifier 2 x 17 W |
| TFA9815T | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Stereo full-bridge audio amplifier 2 x 17 W |
| TFA9815T/N1 | 制造商:NXP Semiconductors 功能描述:Tube |
发布紧急采购，3分钟左右您将得到回复。