参数资料
| 型号： | 4658F-CLEAR-.5"X27YD |
| 厂商： | 3M |
| 文件页数： | 2/2页 |
| 文件大小： | 0K |
| 描述： | TAPE REMOVABLE FOAM 1/2"X 27YD |
| MSDS 材料安全数据表： | 4658F MSDS |
| 标准包装： | 4 |
| 系列： | 4658F |
| 胶带类型： | 双涂层，双面 |
| 胶合剂： | 丙烯酸，100 |
| 背衬，载体： | 聚酯薄膜 |
| 厚度： | 0.031"（31 mils，0.787mm）1/32" |
| 宽： | 0.50"（12.70mm）1/2" |
| 长度： | 81'（24.7m）27 码 |
| 颜色： | 透明 |
| 使用： | 保持，连接，安装 |
| 包装： | 散装 |
| 其它名称： | 00021200385469 02120038546 70006242906 |
3M ? Double Coated Removable Foam Tape with Adhesive 100
4658F
Application
Techniques
Design
Considerations
? Bond strength is dependent upon the amount of adhesive-to-surface contact developed.
Firm application pressure helps develop better adhesive contact and improve bond strength.
? To obtain optimum adhesion, the bonding surfaces must be clean, dry and well unified.
Typical surface cleaning solvents are isopropyl alcohol (rubbing alcohol) and water or
heptane. Note: Carefully read and follow manufacturer ’s precautions and directions for use
when using solvents.
? Ideal tape application temperature is 70°F to 100°F (21°C to 38°C). Initial tape application to
surfaces at temperatures below 50°F (10°C) is not recommended because the adhesive may
become too firm to adhere readily. However, once properly applied, low temperature holding
is generally satisfactory.
? As a general rule, four square inches of tape should be used for each pound of weight to be
supported in static load. More or less tape may be required depending upon the particular
application. User evaluation is, therefore, required to determine optimal tape usage.
? Care should be used when bonding to surfaces with very low internal strength such as painted
plaster board, fabric or cloth, wallpaper, blown vinyl, etc. since delamination of that surface
may occur.
? Care should also be taken with wood veneers and highly polished wood as very glossy
surfaces may leave an image when the tape is removed.
Removal
Techniques
For rigid surfaces, lever or pry apart
the substrates to break the bond.
For flexible surfaces, peel back
slowly to ensure clean removal.
To remove tape from substrate,
pull back corner and peel off quickly.
Application Ideas
? Signs
? Smoke Alarms
? Point of Purchase and other Displays
? Holding Electronic Accessories
? Dispensers
? Nameplates
? Exhibitions
? Air Fresheners
? Picture Frame Tabs
Technical
Information
Product Use
Warranty,
Limited Remedy,
and Disclaimer
Limitation of
Liability
The technical information, recommendations and other statements contained in this document are based upon tests
or experience that 3M believes are reliable, but the accuracy or completeness of such information is not guaranteed.
Many factors beyond 3M’s control and uniquely within user ’s knowledge and control can affect the use and performance
of a 3M product in a particular application. Given the variety of factors that can affect the use and performance of a 3M
product, user is solely responsible for evaluating the 3M product and determining whether it is fit for a particular purpose
and suitable for user ’s method of application.
Unless an additional warranty is specifically stated on the applicable 3M product packaging or product literature, 3M
warrants that each 3M product meets the applicable 3M product specification at the time 3M ships the product. 3M
MAKES NO OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED
TO, ANY IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE OR ANY IMPLIED WARRANTY OR CONDITION ARISING OUT OF A COURSE OF DEALING, CUSTOM
OR USAGE OF TRADE. If the 3M product does not conform to this warranty, then the sole and exclusive remedy is,
at 3M’s option, replacement of the 3M product or refund of the purchase price.
Except where prohibited by law, 3M will not be liable for any loss or damage arising from the 3M product, whether direct,
indirect, special, incidental or consequential, regardless of the legal theory asserted, including warranty, contract,
negligence or strict liability.
ISO 9001: 2008
This Industrial Adhesives and Tapes Division product was manufactured under a 3M quality system registered to ISO 9001: 2008 standards.
Industrial Adhesives and Tapes Division
3M Center, Building 225-3S-06
St. Paul, MN 55144-1000
800-362-3550 ? 877-369-2923 (Fax)
www.3M.com/industrial
Recycled Paper
40% pre-consumer
10% post-consumer
3M is a trademark of 3M Company.
Printed in U.S.A.
?3M 2011 70070739274 (9/11)
相关PDF资料 |
PDF描述 |
|---|---|
| 2-796645-2 | TERM BLOCK HEADER 22POS R/A 5MM |
| 4008-5/8"X36YD | TAPE DBL SIDED FOAM 1/8 X 5/8" |
| 2-796645-1 | TERM BLOCK HEADER 21POS R/A 5MM |
| 2-796645-0 | TERM BLOCK HEADER 20POS R/A 5MM |
| 1-796645-9 | TERM BLOCK HEADER 19POS R/A 5MM |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 4658N | 功能描述:鼓风机 AC TUBEAXIAL FAN RoHS:否 制造商:Murata 产品:Blowers 电流类型:DC 电源电压:5.3 V 气流:1 l/min 轴承类型: 噪声: 速度: 功率额定值: 框架尺寸 (mm):20 mm x 20 mm x 1.85 mm 外壳材料: 端接类型:SMD/SMT 系列:MZB |
| 4658N | 制造商:ebm-papst Inc 功能描述:AXIAL FAN 119MM 220VAC 制造商:ebm-papst Inc 功能描述:AXIAL FAN, 119MM, 220VAC |
| 4659 | 功能描述:电缆固定件和配件 L/T CORDGRIP PG29 CBL DIA 19.0-23.0mm RoHS:否 制造商:Heyco 类型:Cable Grips, Liquid Tight 材料:Nylon 颜色:Black 安装方法:Cable 最大光束直径:11.4 mm 抗拉强度: |
| 46590-000 | 功能描述:板对板与夹层连接器 MAXI PV 008 SPG RoHS:否 制造商:JAE Electronics 系列:WP3 产品类型:Receptacles 节距:0.4 mm 叠放高度:1 mm 安装角: 位置/触点数量:50 排数:2 外壳材料:Plastic 触点材料:Copper Alloy 触点电镀:Gold 电压额定值:50 V 电流额定值:0.4 A |
| 46590-000LF | 功能描述:板对板与夹层连接器 MAXI PV 008 SPG RoHS:否 制造商:JAE Electronics 系列:WP3 产品类型:Receptacles 节距:0.4 mm 叠放高度:1 mm 安装角: 位置/触点数量:50 排数:2 外壳材料:Plastic 触点材料:Copper Alloy 触点电镀:Gold 电压额定值:50 V 电流额定值:0.4 A |
发布紧急采购，3分钟左右您将得到回复。